Category Archives: designs

Anet A8 upgrades : External Mosfet for the Bed

Anet A8 upgrades : Anet A8 3d printerA lot of people are interested in the Anet A8 upgrades, especially the mosfet mod for the heated bed.

The reason for this is a lot of misinformation out on the web about the mosfet on the main board being too small and causing fires.

If you really want to carry out this mod then follow the directions in this post.

We will go through everything you need to do to carry this procedure out safely. Continue reading Anet A8 upgrades : External Mosfet for the Bed

Anet A8 Power Supply – Adding a Mains Socket.

Adding a mains socket to the anet a8 power supply

The anet a8 is powered from the mains.

The supplied kit has a mains lead which is connecteanet a8 power supply mains switchd to the anet a8 power supply directly.

To switch on and off the printer involves pulling the plug.

If the printer starts going wrong and you need to stop it quickly, then pulling the plug may be the only option – can you reach yours quickly?

If not there is a mod you can do easily to add a mains switch and socket.

This mod makes it easy to move the printer around, with out the cable trailing and allows the printer to be switched on and off when stood in front of it.

So would you like to see how easy it is and what is involved? Of course you would. Continue reading Anet A8 Power Supply – Adding a Mains Socket.

Cooling nozzles for 3d Printers – What do you need?

Testing the cooling nozzles on an anet a8cooling nozzles in situ

Are you happy with your prints from your 3d printer? Could your cooling nozzles on your 3d printer be part of the problem?

Check out what it is for and how it does what it does. Continue reading Cooling nozzles for 3d Printers – What do you need?

3d Printer Anatomy : Introduction

Introduction to the 3d printing process

Most people buy a 3d printer, typically a FFF (fused filament fabrication type), after seeing something printed out professionally and after printing something themselves wonder what went wrong.  

3d printer anatomy : printed ball

This is where the 3d printer anatomy series will help in understanding what the limitations are.

Their prints are stepped, often fail, have a lot of stringy bits and droopy bits.

3d printer anatomy: stringy

Do they keep going?– only the inquisitive, the rest are up for sale on Craigslist,Gumtree or E-bay or in the attic along with the breadmaker, sandwich toaster and scalectrix. Continue reading 3d Printer Anatomy : Introduction

3d printer project ideas : How My 3d Printer Fixed A Car

Another post in the 3d printer project ideas series.

others include :

What would you use your 3d printer for?

3d printer project ideas : vw scirocco gtx

My partner has a 1985 vw scirocco gtx. Very nice model. She has just had a bit of work carried out on it to keep it going for a few more years.

It now looks very nice, but it developed a problem.

When started it revved to about 2000 rpm on idle and wouldn’t decrease.

3d printer project ideas : prusa i3

Read more to see how my Prusa i3 3d printer fixed a car… Continue reading 3d printer project ideas : How My 3d Printer Fixed A Car

Things to Make with a 3d Printer

What are things to make with a 3d printer?

I keep coming up with things to make with a 3d printer and thought

things to make with a 3d printer: prusa i3 it was time to chart some of my trials and successes with my printer.

I have now had a 3d printer for a little over a year. What have I got? I have a (#amazon link) prusa i3 clone from china. It is a FFF ( fused filament fabrication) printer, where it extrudes a thin plastic filament which is stuck together. Continue reading Things to Make with a 3d Printer

Learn how to start 3d printing lithophanes

Lithophanes: what are they?lithophanes :opener

Probably being inspired by the early Chinese Ming vases, the Europeans started to produce pictures in translucent porcelain. These could only be viewed clearly when lit from the back.

The word itself comes from a combination of two Greek words ‘lithos’ meaning stone or rock and ‘ phainen’ meaning to cause to appear or to appear suddenly. So lithophanes are either ‘ light in stone’ or ‘ appear in stone’.

They were first introduced to the European market in the 1820’s.

These ‘magical’ pictures were very difficult to make. First an artist would work on a wax coated piece of glass, producing the image with a light behind it or in front of a window. Being back lit he could ‘see’ the finished result. Taking the wax down to a very thin layer would let a lot of light through and leaving the wax thick would produce dark areas.

From these very delicate wax castings a mould was taken, made from plaster. The wax was melted out of the mould leaving a cavity for the porcelain to be forced into every crack and crevice.

The porcelain was very carefully removed.

Then it was baked in an oven at very high temperatures, about 1400C ( 2500F).

The failure rate of these very delicate structures was very high, about 60%, partly due to the different thickness of material and partly due to the delicateness of the finished product. They were very expensive and due to this and the difficulty of manufacture their popularity died out.

They were hung in windows, used as firescreens, where the flickering light would almost cause the picture to come alive. They were used as candleshields, with the flickering light of the candles causing the pictures to dance.

Fast forward

With the advent of modern machinery, there has been a change in the way these wonderful artworks can be produced.

The computer numerical controlled machines has now allowed these pictures to be created at the flick of a switch. All of the work is carried out on the computer.

The artwork is reversed into it’s negative, changed into a height map.

This was then carved out of a solid piece of material, the limiting factor the size of the cutter used in the CNC machine.

Right up to date.lithophane now

The CNC produced very good results, very quickly and with failures being able to be reworked quickly.

But then came the 3d printer.

This marvellous machine which lays a plastic thread down to build up objects is ideal for this task.

Now a print head is guided by a computer generated code to place the plastic thread (extruded filament) onto a flat build platform. This is built up in layers, producing a 3d structure.

Known as additive manufacturing or FFF ( fused filament

lithophane : modelfabrication) this process is capable of producing very thin layers (typically 0.3mm thick).

Detail within the picture can be reproduced accurately and very quickly.

The prints can be produced flat onto the bed or they can be produced upright.

So now a curved print or even a cylindrical print is no problem even to the most basic 3d printer.

The only limitation is the print volume of the printer.

With the advent of led lighting, as naked flames and heat could cause a slight problem with the plastic material, these wonders can now be produced very quickly and easily.

How do you…

From taking the digital picture and then processing it.

One website you can upload photos to and then create a file to print out is here

Navigate to ‘image settings’ at the top

lithophane : image settings

Set the image to positive

Then navigate to ‘ model settings’

Make sure you are

lithophane : site model settingshappy with the maximum size – you can always scale it down in the slicer program.

I tend to set the thinnest layer to 0.4mm – lets more light through – just check your nozzle size is greater than the thinnest layer otherwise it will print nothing.

Going back to the image tab you can load your image – some work

lithophane image pnelbetter than others , make sure there is plenty of contrast in your picture, these work better.

After loading the site should show you the model tab, you can zoom in and rotate the model with your cursor in the area of the

lithophanes model panelmodel.

Download the model stl file.

Use your favorite slicer program to slice it for your printer, and print.

The settings for this are 100% fill, I tend to stand it upright and add a brim( 20 lines). I have started to knock the fan speed down a little to

lithophanes cura settings100 instead of 255, this helps with layer to layer adhesion and results in a less steppy model. The downside of this is that you will reduce the bridging distance.

Don’t forget to print in a light translucent colour otherwise you will not get all of the benefits of the lithophanes picture.

Once printed back light it to see what it looks like. Hold it up to a window. Carefully place in front of a candle or leds ( preferable).

Your picture will be revealed, or like my first one where i forgot to click to positive image and looking into the light it became a negative!!!

I am sure this web site will get a lot of use, as the 3d printing technology grows.

If you don’t fancy doing this then Thingiverse has approximately 400 lithophanes on its site.

You will need an account with thingiverse to customise your image.

There are other ways to create these for yourself but that’s the subject of another post

So for now let’s look back at some lithophanes and see what they looked like then and what we can do now.

Thanks for reading


3d Printer Project Ideas: Apple Mac Power Supply Stand

Another post in the 3d printer project ideas series. This one gives you a walk through for the Autodesk 123design software. To create a stand for an Apple Mac power block.


My partner has an Apple Macbook Pro. The power supply for this unit is an external unit with mains input and dc output.  The mains input is via a lead, which plugs into the side of the power block. The dc output is fed to a magnetically attached connector to plug onto the Macbook

3d printer project ideas: power block Pro

A while ago the power supply failed. It stopped charging the battery on the laptop.

Investigating it, as any engineer would, showed that the dc cable had shorted internally. It appears that this is a weakness in the way apple have manufactured these units and they will fail eventually where the dc cable comes out of the block, especially if the user winds the cable back up onto the cable clips on the power block.

Repairing this cable, the unit works again.

In the meantime we had a Chinese unit, this failed catastrophically. I opened the unit to find that something had blown up – black mark on the inner of the lid. Could I find it? No!! the fault was the same – output dc cable shorted. really frustrating, but it did show that the original apple unit was output short protected and would recover.


Anyway to the project, my partner wanted the power block to stand up, the unit is 79mmx79mmx29mm and laying down, the lower side was getting very hot. So the idea was to stand it up to enable more airflow around the device.

Trying it unassisted the unit just kept falling over, so in steps 3d printing.

I think to myself I can design something to do that easily.

The grey matter starts churning.

The design flow goes something like:

It is too tall to stand up so it needs outriggers.

It also needs to support the sides from both sides.

3d printer project ideas: initial sketches

So flat feet extending sideways and up the sides.

Easy to remove and lay flat after use.

Possible expansion of cable tidy to not strain the output or input cable

out came the sketch book and pencil – yes I still do it this way.

I find it quicker than using a computer. I may investigate a drawing package for the tablet but in the meantime paper and pencil.

The first design was a typical flat piece for the feet with two uprights for the sides of the unit.

I would need two of these, maybe one would get lost? Will need to print off another one. So that idea was put to one side, if I can’t come up with anything else then ok.

The second idea was along the length of the block, with a support at either end and feet out to the side. It’s starting to get large. So possible but don’t stop there.

The next idea was a single sided foot with two supports, one either side of the power block. Ok, getting more original, but if one breaks gets lost then it will fall over.

What about combining these two?

Have three uprights and three feet?

One on the left and two on the right?

With feet extending out?

Small compact and efficient

A single piece and not too large.

This is the design I went with.

Getting it Sorted

I have been trialling Cubify Invent software and after watching the training videos from cubifyfans blogspot, getting the idea of the software it was very easy to produce a fairly complex item – see the salt cellar repair(part 1) and part 2.

The trial has now run out so I was either going to have to purchase the software or try another one.

I had downloaded Autodesk 123design a while ago and never installed it, so this was an ideal time to get it onto my computer and learn it.

After installing it and running it, you are presented with it’s home 3d screen. And…

I played around with the menus, solids and sketches. But had very little headway into the design. I thought I had heard this was supposed to be a very easy cad to learn.

I found this book 3D Printing with Autodesk 123D, Tinkercad, and MakerBot

It covers the basics of 3d printing along with the rest of the suite of software. So although it was not completely dedicated to 123 design it gives enough information along with a few walk through examples to get you started.

Watching the online get started videos from Autodesk was a bit annoying, the person doing the videos assumed a high knowledge of the software and clicked here and there and then tidied up the sketch before extruding it, all in two minutes. No I never went back.

So how to draw up the model to get it printed.

The CAD Process

123design can be thought of in two ways.

One way is like a cnc machine, you create a piece big enough to cover the whole of your model and you then subtract material until what you have left is the object which you want.

The other is to break down what you want into basic shapes, box, cylinder, ball and cone amongst others. These are placed together in a 3d space to create the model you want.

In this tutorial I have gone with the second method. Using basic shapes to make up the model.

In the future I will try the other method and compare it. Similar to a sculptor removing material to find the statue.

I have decided not to do videos of these tutorials at the moment as when I watch them I find it difficult to follow along with the training, having to pause the video and remember what was just done. With the written word you can just refer back to it easily.

So we now know what we are after, three L shaped brackets tied together with a flat slab.

Open the 123 design software and you should be presented with this screen.

3d printer project ideas: initial view

What we need to do is to place a rectangle to fit underneath the power block. This will be 30mmx50mmx2mm. So hover over the primitives menu. A sub menu will appear click on box.

3d printer project ideas:add a box

When you place your mouse over the grid you will be presented with a box, of dimensions 20mm on all

3d printer project ideas: box on screensides. We need to change these to suit what we want.

As the length is highlighted we change this first, set this to 30 and press [tab] it will highlight the width, type in 50 and press [tab], for

3d printer project ideas: dimensioned boxthe height I have selected 2mm, so set the highlighted height to 2. the visual box on the screen will also change in real time and for this one you can place it where you want. I chose one of the darker lines for a reference and clicked with the mouse.

Your first shape is placed.

We now add another box, so hover over the primitives menu and go

3d printer project ideas: first footdown to box, click on it and set the box parameters to length 30, width 10, height 2. place it aligned with the left back corner as shown in the figure and click the mouse to place.

You have added one of the feet.

As all of the feet are the same size we can copy and paste this box.

With the mouse click on the box, the outline should go and stay green.

3d printer project ideas: highlight block

Press [ctrl] and tap the ‘c’ key. This will copy the box. Then press [ctrl] and tap ‘v’ this will paste a second box. It may not be obvious but the movement arrows show that it is there.

3d printer project ideas: ready for movement

We need to move it to the right so click on the right going arrow, this should turn yellow. You can either drag it using this, click and hold the mouse while moving in the direction you want to go, or you can type the distance into the box, as this is blue you can just type the number in, so type in 40 and the box should move 40mm to the right.

3d printer project ideas: two feet

If this doesn’t happen and it moves in another direction, you can either move it back manually or I tend to press [ctrl] and tap ‘z’ this is the undo keys. You will need to copy the box again and try again. It can take a few goes at the start to get used to the keys and clicks, I am still getting used to them.

You end up with a second foot at the other end at the back of the original block.

We now need another foot on the other side of the base block, so copy and paste the original foot again.

This time we want to click on the front arrow, we will move it backwards first. If we typed a positive number into the box it will move in the direction of the arrow. This would move the foot away from the base block, no good. So with this co-ordinate system we can type in a negative number. This will move it in the opposite direction of the arrow – towards the front of the base block. Type 60 into the box and the foot should align itself to the front right hand corner.

Now we need to move it to the middle of the base block. So click on the right arrow and type 20 into the box. This will move it to the centre position.

You end up with a mode like this:

3d printer project ideas: three feet

At this point it is worth saving the model. I tend to work off my computer and as my internet is not fully reliable I will save it to my local computer. Click on the little down symbol to the top left of the screen. Move the mouse down to save a copy and out over my computer.

I have setup a folder in my documents for Autodesk projects, click on the folder you want to save it to, name it what you want to – in my case ‘psu stand 2’ and click on ‘save’

You now have a point to go back to is it all goes horribly wrong. It is a good idea to get into the habit of saving your work regularly. This way you can always just go back a bit to the last save rather than starting from scratch. Don’t worry you will forget to do this and it will go wrong – it is a bit like doing a backup – everybody will do it and knows it makes sense but later – until your computer crashes and you think I should have backed it up. So start getting into the habit of saving after every few moves and especially if you are trying out a new technique. These always go wrong and you will find some commands without a ‘go back’ command – and it is sometimes easier to go back to what you know.

Now we need to add the side pieces, very similar to the feet, adding boxes to all three feet in the upright position.

Again hover over the primitives menu and click on the box.

Come back to the grid with it and type length 2, width 10, height 40, position this as close as you can to the edge of the base block where the foot is at the rear left corner.

To check where you have positioned it you can rotate and zoom in onto the model.

To rotate you press the right button of the mouse and hold while moving the mouse. A two ellipse symbol will appear and the model can be rotated.

3d printer project ideas: first upright

To pan the model – or move it across the screen to reposition it you press the middle mouse button, this will bring up a pair of crossed arrows. You can now drag the model across the screen.

Using these two controls you can look at the upright and see whether it is at the edge of the base block and inline with the foot.

3d printer project ideas: inline foot

If it is you can go no to add another upright, in the same way as we did with the feet. Click on the upright to highlight it and then press [ctrl] and tap the ‘c’ key to copy. Then press [ctrl] and tap the ‘v’ key to paste. Use the arrow keys to move it to the right by 40mm.

3d printer project ideas: second upright

Copy and paste another upright for the front, move this away from you by 32mm ( 30 mm for the base block and 2mm for the thickness of the upright), then to the right by 20mm. This should position it over the foot at the front.

3d printer project ideas: third upright

This has now completed the basic power supply clip, but sharp corners are stress raiser ( where things tend to easily break). They are also a potential hazard to cut you. So it would be nice to round the top edges of the uprights and add a fillet (rounded fill) into the bottom between the uprights and the feet.

To round (fillet) the top edges of the uprights you select the edges you want. We will work on the back left upright first.

Rotate and zoom in ( scroll the middle wheel or click on the
magnifying glass to the right hand side) so you can see the top of the upright.

Click in the middle of the upright top box. And then click

3d printer project ideas: first top filleton the top edge – this will highlight in green. Press [shift] and click on the other 3 edges so that you have all four top edges highlighted.

Now scroll up to the modify menu and find the fillet selection. Click on this.

fillet menu

A box will appear at the bottom of the screen. Make sure that all of the edges are still highlighted and type 0.5 into the box and press [enter]. The top corners will appear rounded.

top filleted

You have filleted the top of the upright.

Now go on to do the other two uprights.

three filleted

We are going to add a fillet between the upright and the foot to add a little strength to the lower corner. So navigate back to the home position, by hovering close to the cube in the top right of the screen and click on the house symbol when it appears.

The upright and the foot at present are separate parts at the moment. This cad system cannot fillet between two separate parts, so we need to join then – or merge them into one part. I did this first by grouping them but this doesn’t merge them to allow the filleting as it keep them as separate parts and just selects all in the group. You need to use the merge selection .

Hover over the combine menu and click on the merge selection.

3d printer project ideas: merge command

A new menu will be on screen showing target solid/mesh and source

3d printer project ideas: initial merge commandsolid(s)mesh(es).

This allows you to select the target solid or mesh to merge the objects with – so click on the foot. This will now have a green outline and the onscreen menu will change over to source sold(s)/mesh(es).

You now click on the upright as we only want these two we are

3d printer project ideas: both parts mergedfinished, but if you needed more you could hold down the [shift] key and click on all the solids you want to select.

Now if you press [return], hover the mouse over the foot. You will see that both the foot and upright are highlighted meaning that these parts are now combined.

3d printer project ideas: both parts merged

If you now zoom in so that you can see the join between the upright and the foot clearly.

Click on the foot to select it. A sub menu appears at the bottom of the screen. None of these operations are what we want. So if you click on the edge between the foot and upright ( it will highlight in green when selected) a little gear icon appears.

fillet local menu

Hover over the gear with the mouse pointer and move to the right to select fillet.

Click on this to bring up the fillet menu.

Set the fillet radius to 2.

front foot filleted

Untick the tangent chain selection.

You will see the fillet in the bottom corner.

Press [return] to accept this and go and merge the two other feet and uprights before filleting them.

all filleted

Click on the home selection, when you move the mouse over the box in the upper right of the screen.

This is the part I printed.

So save the model.

And then navigate to export as 3d.

On the mesh tessellation setting menu presented. Click on medium and combine objects.

Click on ok.

Type in the name you want to save it as and click save.

Post CAD Processing

You can now load your stl model into your slicer for your printer.

I am using Cura here but it can be any of the program, either generic or bespoke to your printer.

3d printer project ideas: old cura

You need to translate the stl file – what the cad saves it in for 3d printing, to code the 3d printer can use to position the print head in 3d space – G-code.

3d printer project ideas: printed part

Setup the correct parameters for your printer and save the file.

Transfer it to your printer and watch the magic begin.

After it has printed and cooled, remove it from the build platform and try your power block.

Mine fitted first time, it is now in constant use as a support for the power block.


I hope you have enjoyed this  ‘how to’  tutorial.

If you have any comments please leave them in the box below.

Future Projects in the 3d Printer Project Ideas Series

If you have any projects which you would like a hand with, to do with 3d printing, please contact me via the contact page. there will be others in the series 3d printer project ideas as soon as I am able to find other things around the house which need fixing.

Thanks for reading


3d Printer Project Ideas: Salt Grinder Part 2

This is the Second installment in the 3d printer project ideas: Salt Grinder repair project, if you missed the first part then click here.

So the first section dealt with the fact that the salt cellar had broken

3d printer project ideas: salt grinder piece broken and I need to fix it – or buy another one.

I was also looking at learning google sketchup, but I found that after having a good go at it I was left with a model without a bottom. I could not fix this and after reviewing another 3d printer, the Cubepro Trio, I came across their basic design software – yes it costs money but is free for 15 cubify invent now

I will review (#amazon link) Cubify Invent shortly as I feel it is a very good CAD system designed specifically for 3d printers. For 3d printer project ideas this software, for the price is excellent value for money, yes there are free CAD programs available and i will trial them. but for ease of use and fit for purpose at the moment I cannot fault the program.

cubifyfans blogspot

Another web site has tutorials on this software, if you intend to get it I would advise watching these to get the concept behind the CAD. This helped no end and so today I looked at the part again and redrew it from the ground up.

Starting with an outside circle and adding an inner ring along with the retainer- the main piece that was broken on the original.

Moving up to the keyways and retaining screw holes.

This time the whole piece was drawn up in an hour. Wow – even for me that was quick!!

3d Printer Project Ideas: first part finished

With sketchup I had to make sure the model was closed and had no spurious lines within the model, not with Cubify Invent, as it is designed to work with 3d printers then it produces a model suitable for 3d printers.

Exporting it to stl out of Cubify invent is simplicity itself (file -export).

Taking it to the machine by the printer and passing it through CURA to get the g-codes, I printed it out.

3d Printer Project Ideas: first printed part

The whole print took 35 minutes. About 1m (3 ft) of material, I am using PLA at the moment.

Offering up the ceramic part to the print I found that the printer had overshot, it was far too tight!! The keyways had a extra piece at the ends, where I need to examine the operation of the printer again. The part could be cleaned up by filing and sanding down, this would prove tricky in the corners of the inner circle so i decided to scrap this one and revisit the cad.

So back to the software. I now needed to modify the part! Not always easy with a lot of cad and with simple models it is sometimes better to start again.

design ideas for 3d printing: finished cad piece

But now I have found out a bit about planes, and the drawing tree down the side (right click and select edit) I decided that it must be possible to modify it.

Going up to the first sketch and editing it to increase the outer diameter was simple. Increasing the inner hole size next.

Moving down the tree and looking at each of the sketches I was able to modify the model to try to ensure a good fit next time.

I allowed +0.5mm for tolerance so hole diameters were opened by 1mm.

The screw hole diameter could only be opened by 0.5mm or the hole would break through the side.

This model was saved as mk2, and run through CURA to get the g-codes.

Another print and removing it off the build platform I set about trial fitting the various parts.

3d Printer Project Ideas:fitted

The ceramic inner dropped in as did the plastic retainer – uh oh !! it seems to be going too well.

Trying the screw they also dropped through the holes.

So assembling the salt cellar with its main grinder piece, I was surprised but pleased that it all fitted back together.

What would I do different?

3d printer project ideas : all back together

The screwdriver bit is very tight when screwing it back together – so don’t forget tool clearance.

Trying the grinder the some of the salt crystals are big and will not go into the grinder mechanism, this would be corrected by leaving more space between the bottom and the inner grinding piece ( make it 1mm longer!!).

Other than this and it appearing a bit ‘heavy’ on the bottom ( thickness of the rim) I am quite happy with this- I may come back to it in the future with an improved design, but for now this is good enough.

So this is the use of a 3d printer – you find something that is broken and design – or copy the broken part – into CAD. Translate that into g-codes and then print it out.

If it need modifying you can do this, reprint and check for fit.

Once it fits you reassemble the finished piece and admire your handiwork.

It is satisfying to be able to produce parts, which in the olden days would only be available to machinists. Now are available to people who can use CAD programs. If you struggle with the CAD then there are houses who will produce the files – or even the finished parts for you. Meaning that that old piece which you have been meaning to get to fixing can now get finally fixed with a proper solution. Or the idea you had about improving that piece and never had the ability to achieve you can now go ahead and draw up in CAD and print it out.

What have you got lying around the house that you mean to get fixed and have been waiting for the ideal moment? Leave a comment below about what your 3d printer project ideas are and we can share in the versatility of the printers.

Thanks for reading




3d printer project ideas: salt grinder repair

While looking around for 3d printer project ideas, I had said to myself that I would make, as far as possible, useful bits!

So I am starting a series of ‘how to design’ repair parts, how to think 

3d printer project ideas : tall grindersthe problem through. How to use the software to get the desired results.

This may be what you are already thinking through, without realising it or you may be just downloading and printing. Either way is good, but if you can design simple parts to repair items that have broken – even better.

We have a tall salt and pepper grinder – two separate items.

A while ago while using the salt grinder a small piece of plastic fell onto my meal.

I didn’t think anything of it until I went to fill it up.

The bottom fell out!!

The rod with the grinder just dropped. It had never done that before!!

On closer examination the piece of plastic that had landed in my meal was a keeper which, when the top nut was undone kept the center rod from falling through.

We had a smaller one to use in the meantime and the tall one was put to one side – other than that it worked ok, the important piece was in good working order so why throw it away?

It is now about 12 months later and it is time I looked at the salt grinder.

Turning it over there are two screw holding the lower piece in.

Removing these the lower piece drops out.

3d printer project ideas: inner pieces

The screwed in bit is made up of two pieces, an outer plastic piece and the inner ceramic grinder part.

The outer plastic piece is not really any use any more – just holding it there are pieces falling off. The salt has completely corroded it. Not the normal corrosion but it appears to have changed the structure of the plastic and it is crumbling away.

Now being careful, I extracted the inner ceramic piece without

3d printer project ideas: salt grinder piece brokendamaging the outer too much.

I need to draw up the outer, to remake it in 3d printed plastic. Will this survive the salt atmosphere? Don’t know – there is very little data on the survival rate of PLA in salt water. Although it is made from corn starch, I am still a little wary of contamination. But it will be a useful exercise to draw up the outer and at least print it off in readiness for more suitable material.

Taking out a note book and pencil – it’s still easier and quicker to do this, unless you have an all- in-one with integrated scanner – then you have the advantage over me. Just scan the object – make sure it is now hollowed out correctly then print it!!(well that’s the theory at least!!)

Up until the time I worked out it was a separate part I was looking to add a strap across the bottom, fixing it with the two screws. I would have rotated the strap through 90 degrees from the screws and affixed it onto a ring around the bottom.

3d printer project ideas: quick sketch

See quick sketch for details.

So using Google Sketchup how do we draw up the piece?

Turning the piece around you can see it is made up of discrete shapes. Tubes, rings, flat pieces so nothing too difficult – except it is the most complex part I have made with Sketchup.

A couple of quick sketches and I think I can simplify the piece from what is there, and thicken up the lower wall, always a bonus.

With things like this you need to look at how you are going to print them, if you get it wrong then there is a good chance an overhang will droop or even worse break. So with this piece print it from the bottom up with the strap at the base and it should be possible.

So taking a break from here until I have drawn up the piece I will post this and get back to you with the drawn up piece.

To be continued

How would you have designed the piece – if you have any ideas then please leave them in the comments box below. Have you any 3d printer project ideas you would like to see me make, leave a reply in the comments box below.

Many thanks for reading